HPE Aruba Networking Certified Associate - Switching
HPE6-A86 Articles & Study Guides
Explore focused explanations and study guides for HPE Network Switching Associate Exam.
21 articles published
Start here
01 · Study & Preparation · Guide
HPE6-A86: Switching Associate Certification Scope and Requirements
HPE6-A86 is the HPE Network Switching Associate Exam required for the HPE Aruba Networking Certified Associate - Switching credential.
Explore HPE6-A86 articles
Showing 1–12 of 21 articles
01 · Study & Preparation · Guide
HPE6-A86: Switching Associate Certification Scope and Requirements
HPE6-A86 is the HPE Network Switching Associate Exam required for the HPE Aruba Networking Certified Associate - Switching credential.
02 · Study & Preparation · Guide
HPE6-A86: Following an Ethernet Packet Through the Network Layers
Following an Ethernet packet through the network layers means separating three decisions: how a signal crosses one link, how a frame reaches the next device on its local network, and how an Internet Protocol (IP) packet reaches a remote…
03 · Study & Preparation · Guide
HPE6-A86: IPv4 Subnetting, ARP and the Next-Hop Decision
To derive an Internet Protocol version 4 (IPv4) subnet, convert the prefix length into a mask, calculate the network boundary, and identify the host range.
04 · Study & Preparation · Guide
HPE6-A86: Selecting AOS-CX Switch Hardware and Software Capabilities
Select an HPE Aruba Networking switch by defining its network role, translating endpoint and uplink needs into hardware requirements, and then confirming every required capability for the exact model and software release.
05 · Study & Preparation · Guide
HPE6-A86: Choosing CLI, Web, Central and API Management
Use the AOS-CX command-line interface (CLI) for direct investigation and precise device work, the local web user interface (Web UI) for visual inspection and supported configuration tasks, Aruba Central for centrally owned management,…
06 · Study & Preparation · Guide
HPE6-A86: Establishing Initial Configuration and Secure Management Access
Commission an AOS-CX switch through a retained console connection: establish administrator credentials, configure the intended management address and virtual routing and forwarding (VRF) context, explicitly enable Secure Shell (SSH),…
07 · Study & Preparation · Guide
HPE6-A86: Configuring VLAN Membership, 802.1Q Tagging and LLDP Validation
Configure a virtual local area network (VLAN) path by assigning untagged endpoint ports to their intended access VLANs and carrying those VLANs across an explicitly restricted trunk.
08 · Study & Preparation · Guide
HPE6-A86: Configuring MSTP and Validating Loop Prevention
Configure Multiple-instance Spanning Tree Protocol (MSTP) consistently on every switch in the intended region: match the region name, revision and complete virtual local area network (VLAN)-to-instance mapping, then choose root priorities…
09 · Study & Preparation · Guide
HPE6-A86: Building and Validating LACP Link Aggregation
Build a Link Aggregation Control Protocol (LACP) aggregation by creating a compatible logical link at both peers, assigning the intended physical members, matching Layer 2 membership and enabling negotiation with at least one active peer.
10 · Study & Preparation · Guide
HPE6-A86: Designing and Validating a CX 6300 VSF Stack
A CX 6300 Virtual Switching Framework (VSF) stack combines member switches into one logical switch with a shared control plane.
11 · Study & Preparation · Guide
HPE6-A86: Implementing Inter-VLAN and Static Routing
To implement routing between virtual local area networks (VLANs), give each VLAN an addressed switched virtual interface (SVI) and make that address its hosts' gateway. Connected routes handle these local subnets for inter-VLAN routing.
12 · Study & Preparation · Guide
HPE6-A86: Understanding and Validating Single-Area OSPF
Open Shortest Path First version 2 (OSPFv2) exchanges link-state information for Internet Protocol version 4 (IPv4), builds a shared view of an area's topology and calculates paths from each router's perspective.